90 research outputs found
Investigation of a direction sensitive sapphire detector stack at the 5 GeV electron beam at DESY-II
Extremely radiation hard sensors are needed in particle physics experiments
to instrument the region near the beam pipe. Examples are beam halo and beam
loss monitors at the Large Hadron Collider, FLASH or XFEL. Currently artificial
diamond sensors are widely used. In this paper single crystal sapphire sensors
are considered as a promising alternative. Industrially grown sapphire wafers
are available in large sizes, are of low cost and, like diamond sensors, can be
operated without cooling. Here we present results of an irradiation study done
with sapphire sensors in a high intensity low energy electron beam. Then, a
multichannel direction-sensitive sapphire detector stack is described. It
comprises 8 sapphire plates of 1 cm^2 size and 525 micro m thickness,
metallized on both sides, and apposed to form a stack. Each second metal layer
is supplied with a bias voltage, and the layers in between are connected to
charge-sensitive preamplifiers. The performance of the detector was studied in
a 5 GeV electron beam. The charge collection efficiency measured as a function
of the bias voltage rises with the voltage, reaching about 10 % at 950 V. The
signal size obtained from electrons crossing the stack at this voltage is about
22000 e, where e is the unit charge.
The signal size is measured as a function of the hit position, showing
variations of up to 20 % in the direction perpendicular to the beam and to the
electric field. The measurement of the signal size as a function of the
coordinate parallel to the electric field confirms the prediction that mainly
electrons contribute to the signal. Also evidence for the presence of a
polarisation field was observed.Comment: 13 pages, 7 figures, 3 table
Luminometer for the future International Linear Collider - simulation and beam test results
LumiCal will be the luminosity calorimeter for the proposed International
Large Detector of the International Linear Collider (ILC). The ILC physics
program requires the integrated luminosity to be measured with a relative
precision on the order of 10e-3, or 10e-4 when running in GigaZ mode.
Luminosity will be determined by counting Bhabha scattering events coincident
in the two calorimeter modules placed symmetrically on opposite sides of the
interaction point. To meet these goals, the energy resolution of the
calorimeter must be better than 1.5% at high energies. LumiCal has been
designed as a 30-layer sampling calorimeter with tungsten as the passive
material and silicon as the active material. Monte Carlo simulation using the
Geant4 software framework has been used to identify design elements which
adversely impact energy resolution and correct for them without loss of
statistics. BeamCal, covering polar angles smaller than LumiCal, will serve for
beam tuning, luminosity optimisation and high energy electron detection.
Secondly, prototypes of the sensors and electronics for both detectors have
been evaluated during beam tests, the results of which are also presented here.Comment: Technology and Instrumentation in Particle Physics 2011, Chicago, IL,
USA. Presented June 11, 2011, and submitted to Physics Procedi
Enabling Technologies for Silicon Microstrip Tracking Detectors at the HL-LHC
While the tracking detectors of the ATLAS and CMS experiments have shown
excellent performance in Run 1 of LHC data taking, and are expected to continue
to do so during LHC operation at design luminosity, both experiments will have
to exchange their tracking systems when the LHC is upgraded to the
high-luminosity LHC (HL-LHC) around the year 2024. The new tracking systems
need to operate in an environment in which both the hit densities and the
radiation damage will be about an order of magnitude higher than today. In
addition, the new trackers need to contribute to the first level trigger in
order to maintain a high data-taking efficiency for the interesting processes.
Novel detector technologies have to be developed to meet these very challenging
goals. The German groups active in the upgrades of the ATLAS and CMS tracking
systems have formed a collaborative "Project on Enabling Technologies for
Silicon Microstrip Tracking Detectors at the HL-LHC" (PETTL), which was
supported by the Helmholtz Alliance "Physics at the Terascale" during the years
2013 and 2014. The aim of the project was to share experience and to work
together on key areas of mutual interest during the R&D phase of these
upgrades. The project concentrated on five areas, namely exchange of
experience, radiation hardness of silicon sensors, low mass system design,
automated precision assembly procedures, and irradiations. This report
summarizes the main achievements
Measurement of shower development and its Moli\`ere radius with a four-plane LumiCal test set-up
A prototype of a luminometer, designed for a future e+e- collider detector,
and consisting at present of a four-plane module, was tested in the CERN PS
accelerator T9 beam. The objective of this beam test was to demonstrate a
multi-plane tungsten/silicon operation, to study the development of the
electromagnetic shower and to compare it with MC simulations. The Moli\`ere
radius has been determined to be 24.0 +/- 0.6 (stat.) +/- 1.5 (syst.) mm using
a parametrization of the shower shape. Very good agreement was found between
data and a detailed Geant4 simulation.Comment: Paper published in Eur. Phys. J., includes 25 figures and 3 Table
Performance of fully instrumented detector planes of the forward calorimeter of a Linear Collider detector
Detector-plane prototypes of the very forward calorimetry of a future
detector at an e+e- collider have been built and their performance was measured
in an electron beam. The detector plane comprises silicon or GaAs pad sensors,
dedicated front-end and ADC ASICs, and an FPGA for data concentration.
Measurements of the signal-to-noise ratio and the response as a function of the
position of the sensor are presented. A deconvolution method is successfully
applied, and a comparison of the measured shower shape as a function of the
absorber depth with a Monte-Carlo simulation is given.Comment: 25 pages, 32 figures, revised version following comments from
referee
ECFA Detector R&D Panel, Review Report
Two special calorimeters are foreseen for the instrumentation of the very
forward region of an ILC or CLIC detector; a luminometer (LumiCal) designed to
measure the rate of low angle Bhabha scattering events with a precision better
than 10 at the ILC and 10 at CLIC, and a low polar-angle
calorimeter (BeamCal). The latter will be hit by a large amount of
beamstrahlung remnants. The intensity and the spatial shape of these
depositions will provide a fast luminosity estimate, as well as determination
of beam parameters. The sensors of this calorimeter must be radiation-hard.
Both devices will improve the e.m. hermeticity of the detector in the search
for new particles. Finely segmented and very compact electromagnetic
calorimeters will match these requirements. Due to the high occupancy, fast
front-end electronics will be needed. Monte Carlo studies were performed to
investigate the impact of beam-beam interactions and physics background
processes on the luminosity measurement, and of beamstrahlung on the
performance of BeamCal, as well as to optimise the design of both calorimeters.
Dedicated sensors, front-end and ADC ASICs have been designed for the ILC and
prototypes are available. Prototypes of sensor planes fully assembled with
readout electronics have been studied in electron beams.Comment: 61 pages, 51 figure
Hadron shower decomposition in the highly granular CALICE analogue hadron calorimeter
The spatial development of hadronic showers in the CALICE scintillator-steel
analogue hadron calorimeter is studied using test beam data collected at CERN
and FNAL for single positive pions and protons with initial momenta in the
range from 10 to 80 GeV/c. Both longitudinal and radial development of hadron
showers are parametrised with two-component functions. The parametrisation is
fit to test beam data and simulations using the QGSP_BERT and FTFP_BERT physics
lists from Geant4 version 9.6. The parameters extracted from data and simulated
samples are compared for the two types of hadrons. The response to pions and
the ratio of the non-electromagnetic to the electromagnetic calorimeter
response, h/e, are estimated using the extrapolation and decomposition of the
longitudinal profiles.Comment: 38 pages, 19 figures, 5 tables; author list changed; submitted to
JINS
Conceptual design report for the LUXE experiment
This Conceptual Design Report describes LUXE (Laser Und XFEL Experiment), an experimental campaign that aims to combine the high-quality and high-energy electron beam of the European XFEL with a powerful laser to explore the uncharted terrain of quantum electrodynamics characterised by both high energy and high intensity. We will reach this hitherto inaccessible regime of quantum physics by analysing high-energy electron-photon and photon-photon interactions in the extreme environment provided by an intense laser focus. The physics background and its relevance are presented in the science case which in turn leads to, and justifies, the ensuing plan for all aspects of the experiment: Our choice of experimental parameters allows (i) field strengths to be probed where the coupling to charges becomes non-perturbative and (ii) a precision to be achieved that permits a detailed comparison of the measured data with calculations. In addition, the high photon flux predicted will enable a sensitive search for new physics beyond the Standard Model. The initial phase of the experiment will employ an existing 40 TW laser, whereas the second phase will utilise an upgraded laser power of 350 TW. All expectations regarding the performance of the experimental set-up as well as the expected physics results are based on detailed numerical simulations throughout
Performance of the CMS High Granularity Calorimeter prototype to charged pion beams of 20300 GeV/c
The upgrade of the CMS experiment for the high luminosity operation of the
LHC comprises the replacement of the current endcap calorimeter by a high
granularity sampling calorimeter (HGCAL). The electromagnetic section of the
HGCAL is based on silicon sensors interspersed between lead and copper (or
copper tungsten) absorbers. The hadronic section uses layers of stainless steel
as an absorbing medium and silicon sensors as an active medium in the regions
of high radiation exposure, and scintillator tiles directly readout by silicon
photomultipliers in the remaining regions. As part of the development of the
detector and its readout electronic components, a section of a silicon-based
HGCAL prototype detector along with a section of the CALICE AHCAL prototype was
exposed to muons, electrons and charged pions in beam test experiments at the
H2 beamline at the CERN SPS in October 2018. The AHCAL uses the same technology
as foreseen for the HGCAL but with much finer longitudinal segmentation. The
performance of the calorimeters in terms of energy response and resolution,
longitudinal and transverse shower profiles is studied using negatively charged
pions, and is compared to GEANT4 predictions. This is the first report
summarizing results of hadronic showers measured by the HGCAL prototype using
beam test data.Comment: To be submitted to JINS
Performance and Molière radius measurements using a compact prototype of LumiCal in an electron test beam
A new design of a detector plane of sub-millimetre thickness for an electromagnetic sampling calorimeter is presented. It is intended to be used in the luminometers LumiCal and BeamCal in future linear e+e- collider experiments. The detector planes were produced utilising novel connectivity scheme technologies. They were installed in a compact prototype of the calorimeter and tested at DESY with an electron beam of energy 1–5 GeV. The performance of a prototype of a compact LumiCal comprising eight detector planes was studied. The effective Molière radius at 5 GeV was determined to be (8.1 ± 0.1 (stat) ± 0.3 (syst)) mm, a value well reproduced by the Monte Carlo (MC) simulation (8.4 ± 0.1) mm. The dependence of the effective Molière radius on the electron energy in the range 1–5 GeV was also studied. Good agreement was obtained between data and MC simulation. © 2019, The Author(s)
- …